This Week's Most Popular Stories About Patio Doors Repair

Patio Doors Repair - how to repair tilt and slide patio door [head to the Articlescad site] to Fix a Wet Dog and Save Your Dog From Cold, Wet Feet

Patio doors are a great way to connect your home with the outside. They offer a relaxing and easy transition. They can also save you money on cooling and heating costs by keeping the air inside your home.

Over time the luster of your sliding glass or French door will fade. Simple repairs can keep your sliding glass or French doors looking like new.

Weatherstripping

It's 5 AM and you're taking your dog out for his morning routine when you stumble into a puddle of water right in front of your sliding patio doors. You look around and discover that the rain of last night was able to get through the seals on your patio doors. This is not going to be a simple task. With a little patience, and a few tools, you can fix it and prevent your dog's feet from getting cold and wet.

It is essential to replace the weatherstripping that seals off the gap between your door and jamb. This will prevent drafts, pests and moisture. This will also help keep your energy bills down. If you look at your doors and windows, you will be able to tell if the weatherstripping needs to be replaced or not.

There are many types of weatherstripping available such as open-cell and felt foam, thermoplastic rubber, as well as metals like copper or bronze. Each has its pros and drawbacks. Felt and open-cell foam are both inexpensive however they tend to be visible and not effective at blocking airflow. Vinyl is more costly, but it's durable and resistant to moisture. Rubber is a good option for areas that have high traffic because it will not wear out as quickly.

To install new weatherstripping, you must first remove the doors to the frame using a screwdriver to loosen the roller adjustment screws. Then, using a flathead screwdriver, remove the plugs that hold the weatherstripping to the bottom of the frame. Then, pull out the weatherstripping that was previously in place and remove any residual adhesive from the bottom of the frame. Then, cut the replacement to the proper length, peel back the plastic strip on one end and apply it to the jamb with the putty knife.

Reinstall the door, and adjust the roller screws to ensure that it sits properly in the track. Apply waterproof caulk to the area where the stationary panel bypasses the sliding door and the edge of the stationary panel meets the frame. This is not as secure a seal than the weatherstripping, but it should work for a while.

Locks and Handles

emergency patio door repair door handles and locks play an important role in the security of your home. As time passes, they may become damaged or worn and need to be replaced. The spindle that connects the inside and exterior handles could also need to be changed.

To replace a handle on a patio door first, remove the old one by unscrewing the screws that hold it in place. Once the old handle has been removed then use a level to ensure that the door is straight before installing the new handle. If the door isn't straight, it could interfere with the lock. This could cause issues in the future.

After you have the new handle Close and open it several times to make sure it works correctly. If you have any issues, consult the manufacturer's instructions or a specialist in hardware for assistance. To avoid problems in the future, it is recommended also to lubricate your lock mechanism with silicone-based lubricant.

The most popular type of patio door lock is a mortise latch. It's typically made of steel and sits inside a pocket carved into the door frame. These locks are commonly used on sliding doors made of aluminum or wood. Before ordering a replacement mortise lock it is important to take some measurements. It is essential to know the location of mounting holes and the position within the lock of the keyway.

Some handles for patio doors come with a locking mechanism built into the handle. The handles have a rectangular key cylinder which is inserted into the handle's keyway. If you have this type of patio door both the inside and exterior locks are combined into one. This type of patio door repair company near me door is often found on aluminum sliding doors.

If the latch on your patio door isn't able to stay closed, the lock tongue may not be catching the hasp in the right way. Another possibility is that the sliding door isn't completely parallel to the jamb on the side. The door should be opened by about an inch, then place it against the frame. This will reveal if there is a gap between the door jamb and the door. If there is a gap, reposition the rollers to the bottom left or the right side of the patio so that it is perfectly parallel to the jamb.

Misalignment

Over time the door's tracks and rollers can lose their proper alignment. This can cause the doors to become stuck or difficult to move. It could also allow cold air and drafts to be able to enter your home, which could reduce the efficiency of your home's energy usage. Fortunately, misalignment is simple to correct and prevent. Applying a silicone-based oil to the tracks and rollers can help your doors move again. It is a good idea to apply this every so often to ensure that your doors are in top operating condition.

Another common issue with patio doors is a damaged screen, which is a nuisance or even a safety risk. It can also prevent the doors from opening and closing correctly, which can result in energy loss. In some cases the screen can be repaired but in others, the door must be replaced. If you're experiencing a ripped screen, wash it thoroughly and make sure not to turn the handles of the door in the wrong way when closing and opening.

Over time, hinges may loosen due to normal wear and tear or excessive usage. This can be fixed by regularly tightening screws. This is a simple job that can be done by yourself, however if you're not confident doing it, you should consult an expert to make sure your doors are properly aligned and secure.

You should also clean the rollers and tracks of your patio repair near me doors on a regular basis. A simple brushing or vacuuming can remove dust and debris that might interfere with the smooth operation of your patio doors. You can utilize a special tool to remove the most stubborn dirt or rust. Checking and tightening the screws on the hinges may help with misalignment however, sometimes it's necessary to replace them completely to ensure a solid, long-lasting seal.

The performance and alignment of your patio doors can be affected when the frames are sagging or sagging. Shifting or warping can occur due to changes in the foundation of your home, but it could be caused due to poor installation or through frequent use. A professional can repair or replace your patio door frame, and ensure that it is properly aligned. This will allow it perform at its best.

Rollers

Patio doors that slide open are ideal for bringing the outside in and providing plenty of light, however they do require some maintenance to keep them sliding smoothly. If you need to pull the handle hard to get the door to move, or it doesn't slide like it used to, it could be the rollers. Over time, the lower track can get clogged by dirt, dust, and mud. This makes it difficult for rollers to move. You can clean it and spray it with a lubricant like 2Slick to see if it helps.

If the tracks have been cleaned, but the rollers are still not gliding freely, then it is time to replace them. There is a variety of replacement rollers that will suit your door and kind of track you have. You can find them at most hardware stores, but will need someone to assist you in removing and replace the rollers. Take a picture of the roller assembly installed within the frame to help the experts identify the exact type and model you require. You can also search for features that can be identified, such as bumps or dimples or cutouts, flared edges or cutouts to narrow down replacement options.

When the rollers are replaced, you'll need to reinstall the sliding door back into its frame. Get some help on this one since the door is heavy. Examine if there are any screws holding the track on either side of the frame. If so check that they're loose enough to allow the bottom of door to fall into the channel above the frame. If there is a screen door, take it from the opening and make sure it's clear of the track and rollers.

Once the new rollers are in, carefully insert the door into the frame and swing it down into place. If the new rollers are adjustable they can be adjusted to allow the door to move to the extent it requires.