Car Key Button Repair: 11 Thing You've Forgotten To Do

Car Key Button Repair

A broken car key is a hassle. It is possible to contact an emergency locksmith service that is available 24 hours a day for help or purchase a new remote.

You may be able save money by fixing your old key fob instead of replacing it. This is especially true when the problem is caused by an old switch or a damaged contact.

Battery

If your key fob's buttons are not responding to your pressing them, it could indicate that the battery has died or is about to reach the end of life. Fortunately replacing the battery is a simple task that can be completed by yourself rather than hiring a locksmith or dealer to do it for you.

First look for the battery compartment. It is usually located on the backside of the automotive key repair fob. It may be hidden behind the cover, which slides out, or an access point which opens when you press the button. Once the compartment is opened then you will find the small battery. It is usually shaped like a small coin and identified with a plus and minus symbol. Remove the battery from the old one and put a brand new one in its place, making sure that the plus and minus marks are correctly aligned.

Once the battery is installed, close the compartment and snap the two parts of the key fob. Make sure you align the pieces and snap them into place properly before closing the door and testing your keys. Press any of the buttons to verify that they function properly.

If your remote control car key repairs keyfob doesn't work after replacing the battery, there may be other issues that require a different type of repair. Physical damage from dropping the fob in a puddle, for example may cause it to stop functioning completely. It could also be due to a problem with the internal electrical system, or it may need to be deprogrammed. See if you can find out what's wrong with your key fob using these other common car remote key fob repair troubleshooting techniques.

Switches

Based on the year and manufacturer, there are various types of switches on the keyfob of your car. The older style keys have an electronic chip that is visible in the case. The newer keys work by sending signals to your car. The buttons on a key can be damaged or worn out due to normal use, regardless of the type. They become difficult to press or not responsive. If you try to press the button too hard it could cause further damage, and could even prevent the key from starting your vehicle in the future.

If your key doesn't seem to be working, you should first try changing the battery. If that doesn't help then you might need to clean your key fob and adjust the switches. These tiny electronic switches are more likely than larger parts of the key to break because they are constantly tossed about.

The switches are rubber-like, and are coated with an electric conductor film that wears down over time. Luckily, they're also tiny and affordable to replace. The old ones are soldered to the circuit board, and you will need to carefully remove them without causing damage to other parts. Then, you can solder in the new ones and reassemble your key fob.

Avoid using your car key fob for more than a couple of hours at a time and avoid leaving it visible. Also, you should find a secure location to store your keys when you aren't making use of it.

If you've tried cleaning your key fob or replacing the battery, lock and key repair near me the problem persists it's probably the right time to seek out a locksmith. A professional locksmith can check the frequency of your key to determine whether your vehicle is able to communicate. They can also open and replace microswitches, alter cases, and much more.

Outer Case

Key fobs spend much of its time bouncing around and if the buttons aren't free to move upwards and downwards within the case, they could become stuck or broken. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it could be necessary to take off the case. If the contacts that the buttons touch are not an ideal fit or are worn, changing them might be the only solution.

Some keys use buttons made of rubber, which be worn out over time. The rubber stretches, nails gouge into it, and the buttons become difficult to press. This can cause the key to fail and in this instance it's time to get the replacement of the case or buttons. This repair involves disassembling the remote, locating the button switches on the circuit board, and then heating the solder before carefully removing them. The circuit board then gets soldered with new buttons. The case can then be put back together with the horseshoe key blade piece attached. The new buttons should be snugly fitted into the case in order to stop them from falling out.

Inner Case

Over time, your key fob's buttons can become damaged or stuck as a result of the continuous rubbing and accidental pressing. Utilizing metallic tape and a hole-punch, you can often quickly fix this problem in the event your car is not at home and the key fob won't work, allowing you to unlock the doors, but not to start the engine. This quick fix may allow you to safely return to your vehicle and complete your trip.