Beware Of These "Trends" Concerning Patio Door Lock Repair

Patio Door Lock Repairs

Over time, wear and tear could cause lock malfunctions. Fortunately, there are several easy and efficient steps that can help restore your uPVC local patio door repairs door's security.

Whether it's realigning the lock or cleaning the locking mechanism, these quick fixes can increase the security of your home.

Clean the Lock

Although patio doors are a great option to let the outside in and keep out the elements however, they can also pose an issue for security when your lock isn't functioning as it should. Over time, wear and tear, hot and cold weather dirt and debris can cause your patio door lock to become difficult to operate. With a little care, you can ensure your patio door repair door's locks always perform effectively.

It is important to first clean the patio door lock as well as all moving parts. This will help remove any coatings or dirt that might be hindering your lock from functioning effectively. Start by wiping all the moving parts of your patio door lock with an aqueous cloth. Then apply a scouring pad or a rough damp cloth to scrub the dirt-infested parts of the frame and door. You should then wipe down the entire lock with a dry cloth to remove any remaining dampness, and allow it to air dry before applying it to the next time.

If you have an exterior door that is fitted with a pin tumbler latch mechanism, you can grease the lock by applying graphite powdered to the key or applying a Teflon-based lubricant like WD-40 Multi-Use. This kind of lubricant can be applied with ease and will not disintegrate over time. If you are unable to locate a suitable lubricant, you might try using a pencil that has a thick tip. Insert the pencil in the lock, then shake it around to spread the graphite.

Regular maintenance is also essential to keep the tracks of sliding patio door lock repairs doors free from dirt, dust and debris. These tracks can be especially vulnerable to snow and ice which can cause them jam or bind and make it difficult for your patio doors to open and close.

You can clean the track rails and rollers on sliding patio door repairs near me patio doors by removing weather stripping that is damaged or dirty. Clean it, and then replace it. Patio door rollers can also be cleaned and sprayed down with an oil that is nonstick.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, are operated by using 3 to 4 or sometimes 5 points locking mechanisms. This includes the lock cylinder and handle which is operated by a key. They require maintenance and the lubrication of moving parts. This can be done with a thin oil (never WD40) and should be done once per year.

If the hinges aren't causing the problem, it could be that the door isn't aligned. It may be rubbing or catching against the strike plate's opening in the frame. Remove the strike plate, and use a sharp tool to expand its mortise. This allows the latch to fit perfectly in the hole and prevents rubbing or catching on the frame.

When the cylinder is out of the way, measure its width with the help of a book or piece wood that fits into the adjustment screw gap above the lock. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the of the cylinder.

Check the lock's width

If your patio door latch isn't able to turn even after cleaning and oiling it's possible that it's not aligned with the strike plate. Verify that the door is balanced, and that the hinge screws are in good condition. In a lot of cases, however, simply moving the strike plate upwards or downwards can fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to properly engage. In this case, enlarge the opening using a chisel and hammer. Then test the latch to ensure that it doesn't touch the jamb frame of the door or get caught on it.

Before purchasing a new lock, you should first identify the type of mortise lock you have. This can be done by looking at the faceplate and determining if it is round or square. Then, look at the screw holes in the existing lock and note the dimensions of each one. This information will aid you in finding an alternative lock that is the same width and will fit perfectly into the hole you have already.

You'll want to identify the mortise lock and examine it for any bends, scratches or other damage that requires to be fixed. A bent or damaged latch is more likely to break than one that's been used much, so be sure to replace the lock with a brand new one that is secure if you find any signs of damage or wear.

Once you've decided on the kind of lock replacement you need It's time to begin the actual repair. Take the old handle and spindle from the patio door, and then put in the new one. Start by putting in the handle inside and aligning it with the spindle and then fixing it with the two bolts or screws that secure it. Once the handle's interior is installed, put in the handle on the outside and screw it into place as well. Once you have completed these steps Test the handles to make sure that they are able to open and close easily and that the latch works correctly with the strikeplate.

Make sure you check the Strike of the door.

The strike plate and the door latch are two parts that work together in order to secure the door. Misaligned strike plate and door latch will result in the latch not being able to latch the door correctly. This problem is usually very simple to solve.

Examine the holes that receive the strike plate to make sure they are free of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that hold the strike plate in place, allowing it to move vertically but not separating it from the door frame. Adjust the strike plate to align its holes for receiving with latch hooks of the door latch. After the strike plate is adjusted then tighten all screws, and test to see if the door closes smoothly.

These plates are difficult to reach for homeowners with sliding patio doors. However they are vital for locking and unlocking your door. The metal plates are situated at the top and bottom jambs of your door, where they serve as the support for the latch. The door latch slides into the strike plate, creating the seal when it is closed. If the strike plate is damaged, rusted, or not installed correctly, it may hinder the latch from locking the door securely.

One of the most common reasons for a patio door lock to become stuck or not close is a misalignment of the latch and strike plate. This can be checked with the "lipstick" test. Rub some lipstick along the edge of the deadbolt and then cover it with masking tape. When you shut the door, the lipstick will leave an impression on the tape, indicating exactly where the latch contacts the strike plate. If the mark is too low or high you can easily alter the strike plate.

If your sliding patio door locks aren't functioning properly they can help keep your home safe from burglars. You need to repair the issue as soon as possible. Follow these steps to repair your patio door lock and restore its functionality.