자유게시판

Why Audi G28 Isn't A Topic That People Are Interested In Audi G28

작성자 정보

  • Brodie 작성
  • 작성일

본문

toyota-logo-2020.pngHow to Replace an audi q5 key G28 Engine Speed Sensor

Charles the Humble Technician teaches you how to replace audi key the G28 Engine Speed Sensor. This sensor is located on the edge of the transmission just above the flywheel ring gear. It sends a signal to the ECU via a grey wire (T55/49), then to the tachometer located in the instrument cluster.

1. Engine Speed Sensor

The grey wire is situated at the edges of the transmission, above the flywheel ring. The sensor transmits signals through the grey wire to pin T55/49. The ECU utilizes this information to control boost and fuel. It also sends an indicator to the G5 Tachometer located in the instrument cluster.

The sensor serves as a reference for comparing with the G40 Camshaft Position Sensor. The ecu must know when the crankshaft reached TDC and also the position of the camshaft, to trigger the spark and injectors.

If this sensor fails the ECU will display the P00160 error, which means the Crank Shaft and Intake Camshaft are not in sync and could indicate the chain is stretched or a jump link on the upper chain of timing. The code won't appear without the additional information provided by other sensors (G4 or G40).

Testing is a bit challenging since there are two connector pins, and they perform different functions but the best method to test it is to measure the resistance between the sensor and the ECU. When the sensor is fully functional, it should read approximately 1000 ohms. Look for signs of coolant, or oil in the connector bay if you have problems with this part.

2. Injectors

Yesterday, while accelerating at full speed from the highway paytoll, I experienced a big cut in power like the engine is running out of gas or injectors aren't firing any more. In the morning, i removed the spark plugs. Three were drenched in gazoline, the fourth was dry. When i crank the engine with no sparks, I put a piece of tissue on top of each injector hole and the 3 drenched with gazoline leap out, however the 4th stay closed. I tried to test the ground connections of ECU pins 14,30 and 48/55. I got 0ohm. Therefore, i think the issue is in another place.

I also tried to reset the PID but with no luck. The car will start when the G28 is disconnected, but it is running fine with the G28 connected. However the intermittent misfire issue continues to occur at higher RPM. The coolant temperature sensor (G62) shows the wrong temperature of -49c even when i unplug it. Also, i noticed that the oil pressure gauge in the cockpit shows 2 bar when the actual pressure is 0.0 if i crank up the engine.

I'm not sure what to do. I feel like i've pretty much eliminated everything else. I'm afraid i may have missed something. If anyone has suggestions, please let me know! TIA!

3. Fuel Pump

The fuel pump in the g28 is activated by a signal from the RPM sensor. The GM-style sender is the same as the G4 and both are used in the 80, 100 200, UrS and RS2 cars so you can easily find one at a salvage yard or in a local parts store. Test them out to do - just put your DMM in resistance mode and take measurements between pins 1 (with the bump on the connector's side up) and 2 (2nd from the left on the black connector's end). They should be infinite ohms.

4. ECU

The ECU in our 20vt turbo (3B AAN ABY) engines needs to be aware of the speed and position of the crankshaft in order to make a decision about timing of fuel injectors, audi lost key etc. In order to do this it makes use of a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If either of these go badly, you will see codes on the diagnostic scanner which could cause engine shut down.

Some of the signs of a failed G28 sensor include an inaccurate rev counter for the gearbox the gears are shifting faster than normal, and/or a misfire when you are in gear. If you have any of these issues, it is likely your sensor is going bad and needs replacing. They are cheap and easy-to-find particularly if they're an Bosch unit like ours. If you prefer, GM's version of this part would be an excellent choice.

5. Tachometer

A malfunctioning engine sensor can cause a variety of issues in your audi car key cover. It's an essential component of your replacement audi key's transmission, as it sends information to the ECU about how fast or slow the vehicle's crankshaft is rotating. If this sensor fails, it can cause problems for the transmission as well as the rest of the car's components.

Saab-logo.jpgThe G5 engine speed sensor is located on the outside of the transmission, above the flywheel ring gear and sends a signal to the ECU at pin T55/49 via an uncolored wire. The ECU utilizes this signal to control the flow of fuel and boost and also to timigrate. It also transmits it to the G5 Tachometer located in the instrument cluster. You can determine if the sensor is in failure by examining the continuity from the sensor to the tachometer. You can also verify continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79trace [79]), and between pin T6a/1 as well as pin T26a/12. There should be the resistance to be around 1000 ohms between these points. This part is common across the audi etron key 80-100-200-RS2 range, from the 1985 MC all the way up to the 1997 UrS AN and 1995 RS2 Du So, you may find good ones in wrecking yards.

관련자료

댓글 0
등록된 댓글이 없습니다.

최근글


새댓글


  • 댓글이 없습니다.