See What Saab 9-3 Key Replacement Tricks The Celebs Are Using

How to Replace the Replacement Key Battery For the saab 9-3 key programming 9-3

saab 900 key owners must follow a set of specific steps to add an additional ignition key. It requires dealer service using a handheld computer called Tech-2. Then the transponder must be replaced and a key must be purchased.

Make sure to rotate your keys in order to prevent one from wearing out faster than the next. This will help keep your keys in good condition.

Replacement Case

Unlike the classic Saab keys of the past keys, the modern key fobs are equipped with electronics which makes it more difficult to copy. This has made stealing cars much more complicated than it was 20 years ago. It also makes it more expensive to replace lost keys.

Every owner of a 9-3 Saab 9-3 Key Replacement should have at a minimum two functioning keys. If one of them is lost, it is expensive to purchase a new one for the car because it involves replacing the CIM module and re-programming the locking cylinders. Dealers usually charge between $100 and $200 to complete this.

There are several ways to get around these high cost. Certain parts suppliers will utilize the code of a spare key to cut a brand new metal blade for a fraction of that of a dealer. The key must be the exact same as the original to allow it to work in your vehicle.

Follow these steps to replace the case. You'll need a flathead screwdriver as well as some patience. With the screwdriver, break away the plastic and take out the emergency key. Once you have the case open, remove the electronic components and place them into your new case. Put the correct key and badge into the case.

Replacement Battery

The Saab 9-3 replacement battery is a low-cost component that can be quickly and easily replaced. This YouTube DIY video Cyclone Cyd, a user on YouTube, explains how to replace the battery of the remote key fob in just four steps. This tutorial will work with any modern Saab key fob. However, the procedure might differ slightly.

The first step is to find the button that opens the backup key inside the fob. This button is typically located on the back of your fob, close to the Saab Logo. Use a flathead to insert the screwdriver in the small hole in this button. This should be sufficient to let the fob case open so that you can change the battery.

Once you have installed the new battery CR1632, you are able to reassemble your remote key fob. Then, you can program it into your car. The procedure should take no more than an hour at most. It is a very simple process that does not require any special equipment.

If you lose your key, the process is more complicated however, it can be accomplished. The dealer has to verify the VIN of the car, and then order a replacement key blade and TWICE module, both with the proper unique code. The dealer will then have to program the key using MDI which is a new software tool.

Replacement Key Fob

The key fob is the part that locks and unlocks your car. It has a battery inside. The batteries are able to last for, and they will eventually go out of service. This is a typical issue that occurs with all vehicles and the good news is that you can change the batteries in many key fobs without having to replace the whole case. You can buy replacement fobs on Amazon that have all the electronics already installed, which means you can just pop open the case and replace the batteries that were in the case. You'll need to take out the emergency key before you replace the batteries. To do this, you need to insert an small screwdriver with a flat head into the slot that is in the middle. The case should split when you rotate the screwdriver around it.

When you're ready to replace your keys, ensure that you have a spare, as this will reduce the total cost by a significant amount. If you have a spare, you can ask the dealer to cut the new key and program it to the car, which is much cheaper than replacing the entire key fob.

If you don't have a spare car key, you can add an additional key to your car, but this will require a lot of research and effort. Adding a second key costs several hundred dollars and also requires programming of the car's computer. This can be accomplished by a professional, but it's an expensive option for the majority of owners.

Replacement Ignition

In contrast to the earlier saab 9-3 key programming automobiles, the current saab spare key 9-3 models feature an upgraded alarm system that is built on a key code. If you lose your sole key, it could be costly to get another one because the car must include a computer and be programmed to accept a new key. Dealers can even charge hundreds of dollars to program an additional key even if they're unable to complete the task.

Dealers will charge you a premium to replace your car's computer (also known as the CIM or SAAB twice) when you lose your only working key. We can reprogram the EEPROM in your car computer so that it's prepared for a new key. This will save you more than 50% on the cost you would pay a dealer.

If you've been an owner of a 03-11 SAAB 9-3, you likely realize that the ignition key isn't all that robust. If your ignition key isn't functioning properly, you must look into replacing it. They can become very sticky and the buttons have been known to fall off. Fortunately, replacing the ignition key isn't as difficult as it seems, and it is fairly easy to do with the appropriate tools.